Epoxy Density: Convert Volume (oz/ml) to Grams for Weight Mixing
Updated 2026-11-18
If your epoxy kit is mixed by weight, a cup marked in fluid ounces is not enough. You need mass: grams or ounces-weight. Mass comes from volume times density (specific gravity). If the kit is mixed by volume, you do not have to convert to grams — but you still should not treat a 2:1 volume ratio as a 2:1 weight ratio, because Part A and Part B often have different densities. This guide shows the conversion, how to use the density field in the epoxy resin calculator, and a worked example so you can check the math.
Use the mixed or part-specific density printed on your TDS. EpoxyMath does not assign a single “true” density to all epoxy. The calculator’s default of 1.1 g/cm³ is a placeholder, the same approximation noted in the on-page unit conversions — replace it when you have the sheet.
Quick answer
Weight is volume times density. In metric units the arithmetic is direct, because 1 milliliter of water has a mass of about 1 gram, and specific gravity (SG) is density relative to water:
mass (g) = volume (ml) × density (g/ml)
= volume (ml) × specific gravity (unitless, at the TDS reference)
One US fluid ounce is 29.5735 ml. So at a placeholder density of 1.10 g/ml, 1 fl oz of mixed epoxy has a mass of about 32.5 g. Enter your volume and your TDS density in the epoxy calculator to get grams, then split Part A and Part B by the labeled weight ratio. If the label is a volume ratio, measure by volume instead — see volume vs weight.
Convert volume to grams and split A/B →
1. Density, specific gravity, and the TDS number
Density is mass per unit volume. In these conversions we use grams per milliliter, which is the same as grams per cubic centimeter. Specific gravity is that density divided by the density of water at the reference temperature the manufacturer used. For workshop math, a TDS line that says “specific gravity 1.10” or “density 1.10 g/cm³” can be used as 1.10 g/ml.
Check which density the sheet is giving you:
- Mixed epoxy (A+B after combining) — useful for converting a finished pour volume into an approximate kit weight.
- Part A alone and Part B alone — the right numbers if you weigh each side separately.
- Units and temperature. A density at 25 °C is the one that matches a shop that is actually near 25 °C; do not over-precision a number you then measure in a cold garage.
Many published mixed-epoxy specific gravities fall somewhere near 1.05–1.20 g/cm³. That band is a planning range already used as context on EpoxyMath calculators, not a measurement of your kit and not an average of a survey. If the sheet says 1.13, use 1.13.
2. Unit conversions (the same ones the calculator uses)
1 US gallon = 231 in³ = 128 US fl oz = 3,785.41 ml
1 US fl oz = 1.8047 in³ = 29.5735 ml
1 in³ = 16.387 ml
mass (g) = volume (ml) × density (g/ml)
pounds = grams ÷ 453.592
Example: 1.00 US gallon at the calculator’s placeholder density of 1.10 g/ml is 3,785.41 × 1.10 = 4,164 g, or about 9.18 lb. At 1.05 g/ml the same gallon is about 8.76 lb; at 1.20 g/ml it is about 10.01 lb. The volume did not change — only the mass did.
3. Planning table at four placeholder densities
These figures are for if your mixed density is the value in the header. They are not product prices, not brand ratings, and not a substitute for the TDS.
| Volume | At 1.05 g/ml | At 1.10 g/ml | At 1.15 g/ml | At 1.20 g/ml |
|---|---|---|---|---|
| 1 US fl oz (29.57 ml) | 31.1 g | 32.5 g | 34.0 g | 35.5 g |
| 16 US fl oz (473.2 ml) | 497 g | 520 g | 544 g | 568 g |
| 1 US gallon (3,785 ml) | 3,975 g (8.76 lb) | 4,164 g (9.18 lb) | 4,353 g (9.60 lb) | 4,542 g (10.01 lb) |
To check one cell: 16 fl oz × 29.5735 ml/fl oz × 1.10 g/ml ≈ 520 g. If you change density or volume, rerun that product rather than scaling from memory in a different unit system.
4. Why a volume ratio is not a weight ratio
If Part A and Part B had the same density, a 2:1 volume mix would also be 2:1 by weight. In real kits they often do not match. A heavier resin and a lighter hardener mean 2 volumes of A plus 1 volume of B is more than twice as much mass of A as of B.
Illustration only — these part densities are labels for the arithmetic, not a named product:
Suppose Part A = 1.16 g/ml and Part B = 1.00 g/ml.
2:1 by volume, using 2 ml A + 1 ml B:
mass A = 2 × 1.16 = 2.32 g
mass B = 1 × 1.00 = 1.00 g
weight ratio A:B = 2.32:1, not 2:1
2:1 by weight, using 30 g total:
mass A = 20 g, mass B = 10 g
volume A = 20 ÷ 1.16 ≈ 17.2 ml
volume B = 10 ÷ 1.00 = 10.0 ml
volume ratio A:B ≈ 1.72:1, not 2:1
The labeled method wins. Weighing a kit that is specified by volume, or cup-measuring a kit that is specified by weight, is a common way to get a sticky, soft, or brittle cure — the recovery path is in wrong mix ratio and sticky / not curing.
5. Worked example: 12 fl oz mixed, 2:1 by weight, density from the sheet
You have already sized a small pour at 12 US fl oz mixed (about 355 ml). The TDS lists a mixed specific gravity of 1.10 and a mix ratio of 2:1 by weight. (If your sheet lists different numbers, substitute them.)
volume = 12 × 29.5735 = 354.88 ml
mass_total = 354.88 × 1.10 = 390.4 g
2:1 by weight:
Part A = 390.4 × 2/3 = 260.2 g
Part B = 390.4 × 1/3 = 130.1 g
If the same 12 fl oz were instead specified 2:1 by volume, you would measure 8.0 fl oz of A and 4.0 fl oz of B and you would not use the 260 g / 130 g split. If Part A and Part B have separate densities, weigh each side with those densities rather than with a single mixed number.
Add waste the usual way: if you want 15% extra mixed epoxy, use 12 × 1.15 = 13.8 fl oz as the volume input, then convert. The waste percentage guide explains why that buffer exists; the calculator’s waste field applies it before the gram result.
Enter 12 fl oz and your TDS density →
6. Using the density field without double-converting
The main epoxy calculator already reports approximate weight as ml × density, with a default of 1.1 g/cm³ if you leave the field alone. Edit the field to the TDS value, include waste if you want it, then read grams (and the A/B split if you choose a ratio). Do not convert ounces to grams by hand and then also type a second conversion into another tool, or you will double-count.
A scale that reads grams is the right tool for a weight-ratio kit. Tare the mixing cup, add Part A to the target mass, then add Part B to the total. A kitchen scale that only reads ounces-weight can work if you convert grams ÷ 28.3495, but grams are less awkward at these sizes.
Related guides
- Epoxy mix ratio: volume vs weight
- What happens at the wrong mix ratio
- Why is my epoxy sticky / not curing
- How much extra epoxy (waste %)
- Epoxy shelf life and expired resin
- Epoxy coverage per gallon
Summary
To convert epoxy volume to grams, multiply milliliters by the density (specific gravity) on the TDS. One US fl oz is 29.5735 ml; at the calculator’s 1.10 g/ml placeholder that is about 32.5 g per fluid ounce, or about 9.18 lb per US gallon — replace 1.10 with your sheet’s number. A volume mix ratio is not automatically the same as a weight ratio when Part A and Part B have different densities. Measure the way the label states, and use the epoxy resin calculator to apply waste, density, and the A/B split in one pass. Estimates only — follow your TDS and SDS.