Home › Guides

How Much Does It Cost to Epoxy a Garage Floor?

Updated 2026-11-18

The cost to epoxy a garage floor splits into two different questions: what the materials add up to if you coat it yourself, and what a contractor will charge to prep, coat, and warrant the slab. This guide keeps those apart. For DIY, you multiply each layer’s gallons (and flake by the pound) by the prices on your receipt or cart — EpoxyMath does not list brand shelf prices. For professional work, the only honest number is a written local quote; below we cite dated, location-specific ranges that contractors have published, not a national average.

Gallon math for floor systems already lives in how much epoxy you need for a garage floor. This page uses that guide’s planning thicknesses and 1-car / 2-car examples, then turns them into a cost formula. Kit labels and the technical data sheet (TDS) override every estimate here.

Quick answer

DIY material cost is:

DIY materials = (primer gal × price/gal) + (body/build gal × price/gal) + (topcoat gal × price/gal) + (flake lb × price/lb) + supplies

Using the same planning examples as the coverage guide — a ~220 sq ft 1-car bay and a ~440 sq ft 2-car bay, not standard garage sizes — a primer and topcoat at 6 mils each plus a 16-mil body coat, with a 15% waste allowance, land near 0.95 + 2.5 + 0.95 gal (1-car) or 1.9 + 5.0 + 1.9 gal (2-car). Full-broadcast 1/4-inch flake at a published 5–7 sq ft per pound is about 31–44 lb or 63–88 lb. Plug your own unit prices into the epoxy cost calculator.

Hired installation is a different number: it bundles grinding, repairs, labor, and usually a complete system. Two contractors who published 2026 local ranges (Dallas–Fort Worth and Las Vegas) are quoted in the professional section below. Those figures are their ranges for their markets, not a bid for your garage.

Enter your prices in the cost calculator →

1. Measure the floor first

Measure length and width wall-to-wall, subtract permanent islands or stairs, and use your square footage. The 220 sq ft (about 20 × 11 ft) and 440 sq ft (about 20 × 22 ft) figures used here are worked examples from the garage floor coverage guide. Real one- and two-car garages often fall in a wider band; do not treat 220 or 440 as a standard size when you price a job or compare a contractor’s takeoff.

2. DIY materials: gallons × your unit price

A typical garage floor system is a thin primer or body coat, an optional vinyl-flake broadcast, and a separate topcoat (often epoxy or polyaspartic). Calculate each liquid layer from its TDS wet-film target or published spread rate, then price it separately — primer, body coat, and topcoat are often different products at different prices.

Gallons (one layer) = area_sq_ft × 144 × (mils ÷ 1000) ÷ 231 = area_sq_ft ÷ (1604 ÷ mils) Gallons with waste = Gallons × (1 + waste_fraction) Flake (lb) = area_sq_ft ÷ (sq ft per lb from the flake TDS) = area_sq_ft × (lb per sq ft from the flake TDS)

The coverage guide walks through this conversion and why tabletop flood-coat math (around 1/8 inch) is the wrong product class for floors. For waste on rollers, cuts, and pot residue, that guide uses a 15% planning allowance, and more (15–25%) on freshly ground, thirsty concrete. Use the allowance that matches your slab and the TDS; then convert kit prices to a mixed price per gallon:

Price per gallon = kit price ÷ mixed volume of the kit (gal)

If the label lists fluid ounces, divide by 128; if liters, divide by 3.785. Count Part A and Part B together, not one side only.

Planning gallons for the 220 and 440 sq ft examples

The body-coat and topcoat gallons below reuse the coverage guide’s planning thicknesses (16-mil body, 6-mil topcoat) and 15% waste. A 6-mil primer is added as its own line so primer, body, and topcoat stay itemized. These are planning examples, not a specification — if your TDS gives a spread rate in sq ft per gallon, use that rate instead of the mil formula.

Layer (planning)~220 sq ft example (1-car)~440 sq ft example (2-car)
Primer at 6 mils + 15% waste0.95 gal1.9 gal
Body / build coat at 16 mils + 15% waste2.5 gal5.0 gal
Clear topcoat at 6 mils + 15% waste0.95 gal1.9 gal
Liquid coatings, subtotalabout 4.4 galabout 8.8 gal

Check: theoretical coverage is about 1604 ÷ mils square feet per gallon (100% transfer). At 6 mils that is ~267 sq ft/gal, so 220 ÷ 267 ≈ 0.82 gal before waste and 0.95 gal after 15%; at 16 mils, ~100 sq ft/gal, so 220 ÷ 100 ≈ 2.19 gal before waste and 2.5 gal after 15%. The 440 sq ft column is double. A Sherwin-Williams Resuflor MPE application sheet dated February 2025 lists a pigmented build coat at 200 sq ft per gallon at 8 mils wet/dry, which matches the same 1604 ÷ mils relationship (1604 ÷ 8 ≈ 200). Your product may be thicker, thinner, or not 100% solids — follow its sheet.

If you skip a separate primer on a tight, well-prepared slab, drop that line. If the topcoat is a different chemistry (for example a polyaspartic), do not reuse the body-coat price or spread rate.

Flake, priced by the pound

Full-broadcast vinyl flake is sold by weight, not by epoxy gallons. The epoxy volume barely changes; the flake line item does. Torginol’s Polymer Flake technical data sheet (February 2025) publishes these full-coverage guidelines in square feet per pound:

The same sheet notes that coverage guidelines are approximations. Full broadcast is usually thrown to rejection, then loose excess is swept up after the receiving coat cures — order from the system chart, and do not assume swept flake can be reused unless the manufacturer says it can.

Full-broadcast 1/4" or 1/8" flake (5–7 sq ft/lb)~220 sq ft example~440 sq ft example
Pounds to plan31–44 lb63–88 lb

A Miracote MiraFlor Flake Full Broadcast product sheet (document MIR.260, dated 12-10-2012) lists a broadcast of 14 lb per 100 sq ft (0.14 lb/sq ft), or about 31 lb and 62 lb on the same two example floors — at the light end of the Torginol 5–7 sq ft/lb band. If your current flake TDS differs, use it.

Worked cost examples (placeholder prices only)

The letters below are placeholders. Replace them with what you actually pay. EpoxyMath does not treat them as market prices.

1-car example (~220 sq ft): Materials ≈ 0.95P + 2.5B + 0.95T + (31 to 44)F + S 2-car example (~440 sq ft): Materials ≈ 1.9P + 5.0B + 1.9T + (63 to 88)F + S Cost per sq ft = Materials ÷ your measured area

To price one liquid layer in the cost calculator, enter the gallons (or the area and mil thickness) and your price per mixed gallon or per kit. Repeat for each product, then add flake and supplies by hand — the calculator estimates epoxy material cost, not labor or broadcast media.

Supplies to price locally (no amounts invented here)

Besides resin and flake, most DIY jobs buy or rent:

Reusable tools can be counted at a fraction; consumables and a one-weekend grinder rental belong in S at what you actually pay. Prep quality is also what most professional quotes are really charging for.

3. Professional installation: use dated local quotes, not a national average

A contractor’s price usually includes diamond grinding or other specified prep, normal crack repair, the coating system, and cleanup — and it varies with slab condition, moisture, old coatings, access, and the finish you choose (solid color, flake, quartz, or metallic). EpoxyMath does not publish a nationwide “going rate,” and we do not invent brand installation prices. The useful method is to get more than one written quote and compare them on the same scope:

You can still use the DIY formula to see roughly how much of a quote might be material versus labor and prep. The rest is local.

Published local ranges (examples, not your bid)

These figures come from contractor pages that name a service area and a date. They use their own garage-size bands, which are not the 220 / 440 sq ft examples above. Do not multiply their per-square-foot ranges by 220 or 440 and treat the result as a national estimate.

Dallas–Fort Worth, Texas — Signature Epoxy Floors (Alvarado, TX), page updated October 2026, describes professionally installed prices that include diamond grinding, normal crack repair, every coat, and cleanup:

System (installed, DFW)Published range
Flake (epoxy base + polyaspartic topcoat)$4–$7 per sq ft
Quartz broadcast$6–$9 per sq ft
Metallic epoxy$10+ per sq ft

On the same page, they publish whole-garage flake totals of $1,000–$2,100 for a 1-car bay they describe as 250–300 sq ft, and $1,600–$3,500 for a 2-car bay they describe as 400–500 sq ft (metallic starts at $2,500+ and $4,000+ in those same size bands). They also state that removing an old coating or paint typically adds about $1.50–$3 per sq ft in that market. Those add-on and size figures are theirs, as of that October 2026 page — not a general rule.

Las Vegas, Nevada — ProShield Epoxy, article by Julian Cruz dated April 3, 2026, covering the Las Vegas metro (and a stated 20-mile radius), publishes:

System (installed, Las Vegas)Published per sq ftTheir 2-car (400–500 sq ft) total
ProFlake (epoxy + polyaspartic)$3.50–$6$1,800–$3,000
Solid color epoxy$3–$5$1,500–$2,500
Metallic epoxy$7–$12$3,500–$5,500

The same article also states a broader professionally installed range of $3.50–$12 per sq ft in Las Vegas, and $1,800–$5,000 for a 400–500 sq ft 2-car garage depending on the system. Concrete repairs and old-coating removal, they note, can add further cost; they describe extensive damage as potentially adding $1–$3 per sq ft.

If you are not in those markets, treat the tables only as a reminder that published local ranges already differ by city, system, and what is included. Get quotes where the slab actually is.

4. What moves the number

Tips for a tighter estimate

  1. Measure the floor yourself and write the square footage on the same sheet as your product list.
  2. Read the TDS for each layer’s spread rate or wet mils before you shop kits.
  3. Convert every kit to a mixed price per gallon so products are comparable.
  4. Itemize primer, body coat, flake, and topcoat; then add supplies.
  5. For hired work, compare written scopes, not headline per-square-foot numbers alone.

Related guides & tools

Sources

Summary

DIY garage floor epoxy cost is the sum of primer, body coat, topcoat, flake, and supplies, each priced from what you pay — not from a brand list on this site. For the coverage guide’s example floors, a 6-mil primer, 16-mil body coat, and 6-mil topcoat with 15% waste come to about 4.4 gallons on ~220 sq ft and 8.8 gallons on ~440 sq ft, plus roughly 31–44 lb or 63–88 lb of full-broadcast 1/4-inch flake at Torginol’s February 2025 5–7 sq ft/lb guideline. Professional installed prices belong on dated local quotes; the Dallas–Fort Worth and Las Vegas ranges above are cited as published examples only. Get your gallons from the garage floor coverage guide, then run your unit prices through the epoxy cost calculator. Estimates only — follow the floor system TDS and SDS.